--- title: "2068 Fix Star NX-1000/Aerco Centronics I/F Fix" type: "article" slug: "2068-fix-star-nx-1000-aerco-centronics-i-f-fix" url: "http://localhost/article/2068-fix-star-nx-1000-aerco-centronics-i-f-fix/" markdown_url: "http://localhost/article/2068-fix-star-nx-1000-aerco-centronics-i-f-fix.md" published_at: "2020-10-27T17:17:13+00:00" modified_at: "2026-11-15T10:43:00+00:00" featured_image: url: "http://localhost/wp-content/uploads/2022/04/20230809-041332.jpg" excerpt: "I purchased a new Star NX-1000 Multi-Font printer about a month ago only to find that it would not work with the AERCO Centronics printer interface and the 2068. I started writing requests for help to everyone I could think of and today I received word back from John Oliger with a suggestion for a…" post_tag: - name: "AERCO" slug: "aerco" taxonomy: "post_tag" url: "http://localhost/tag/aerco/" - name: "Full Text" slug: "fulltext" taxonomy: "post_tag" url: "http://localhost/tag/fulltext/" - name: "Hardware project" slug: "hardware-project" taxonomy: "post_tag" url: "http://localhost/tag/hardware-project/" - name: "TS 2068" slug: "ts2068" taxonomy: "post_tag" url: "http://localhost/tag/ts2068/" model: - name: "Timex/Sinclair 2068" slug: "ts-2068" taxonomy: "model" url: "http://localhost/model/ts-2068/" indiv: - name: "Richard Hurd" slug: "richard-hurd" taxonomy: "indiv" url: "http://localhost/indiv/richard-hurd/" publication: "Sinc-Link" publication_r: id: 10240 title: "Sinc-Link" type: "periodical" url: "http://localhost/periodical/sinc-link/" authors: "Richard Hurd" volume: "8" issue: "1" issues_articles: - id: 26583 title: "Sinc-Link v8 n1" type: "issue" url: "http://localhost/issue/sinc-link-v8-n1/" pages: "20" pubdate: "January/February 1990" archive_link: false volumeissue: "v8n1" companies_articles: - id: 10635 title: "AERCO" type: "company" url: "http://localhost/company/aerco/" --- # 2068 Fix Star NX-1000/Aerco Centronics I/F Fix I purchased a new Star NX-1000 Multi-Font printer about a month ago only to find that it would not work with the [AERCO](http://localhost/company/aerco/) Centronics printer interface and the 2068. I started writing requests for help to everyone I could think of and today I received word back from [John Oliger](http://localhost/indiv/john-oliger/) with a suggestion for a fix. Invert the STROBE line. It worked! First I cut the trace on the AERCO board. I had a 74LS04 IC in the spares box and soldered wire-wrap wire to pins 1, 2, 7, and 14 then to the connections shown. Pin 1 of the 74LS04 to point a of the AERCO I/f and pin 2 goes to point b of the AERCO I/f. Just track down a ground pad and a plus 5 volt pad for power. I used a small piece of double sided sticky tape to hold the IC in place. [![AERCO interface board, solder side (rear view), showing the cut in the STROBE trace and points a and b](http://localhost/wp-content/uploads/2020/10/sinclink-23494-1-1024x688.png)](http://localhost/wp-content/uploads/2020/10/sinclink-23494-1.png)AERCO interface board, solder side (rear view), showing the cut in the STROBE trace and points a and b [![74LS04 connections: pin 1 in, pin 2 out, pin 7 gnd, pin 14 +5 volts](http://localhost/wp-content/uploads/2020/10/sinclink-23494-2-1024x539.png)](http://localhost/wp-content/uploads/2020/10/sinclink-23494-2.png)74LS04 connections: pin 1 in, pin 2 out, pin 7 gnd, pin 14 +5 volts *** ### Editor’s Note Since a large portion of Sinc-Link is published on a Star NX-1000 driven by a TS2068 and I have had no problems, I must assume that my [Peter Hacksell](http://localhost/indiv/peter-hacksel/) AERCO-style printer interface solves the problem described above. [Hacksell boards](http://localhost/company/hacksel-electronics/) are still available in the Toronto area via our club. For more info just write us. J.T.